Mandalika Varuna Perkasa

AIRBLAST BLAST HOSE AIRBLAST LONG VENTURI NOZZLE ( BLASTING )

Airman

DIAPHRAGM HOSE RADIATOR OLI SEPARATOR AIRMAN

Clemco

ADDHESION - PULL OFF ADHESION - PUSH OFF Adhesion Tester Climatic Conditions Dry Film Thickness Elcometer 456 Coating Thickness Gauge Probe Range Inspection Accessories MATERIAL THICKNESS Pinhole & Porosity Detector Precision Thickness RH, Dewpoint & Temperature Surface Preparation - Blasting Surface Preparation - Cleanliness SURFACE PREPARATION - PROFILE Surface Prepation - Condition SURFACE PROFILE Ultrasonic Couplant Wet Film Thickness

Flotech

Flotech 30:1 ( SPRAY PAINTING ) FLOTECH 45:1 ( SPRAY PAINTING ) Repair Kit Airmotor 30:1 Repair Kit Airmotor 45:1 , 63:1 , X68:1 Repair Kit Lower Pump 30:1 Repair Kit Lower Pump 45:1 Repair Kit Lower Pump 63:1 Repair Kit Lower Pump X68:1 Repair Kit S-Plus Gun Flotech DK345-RK

Graco

286XXX RAC 5 SWITCH TIP ( SPRAY PAINTING ) AIRMOTOR XTREME GRACO BLUEMAX PAINT HOSE FILTER & STRAINERS LOWER PUMP EXTREME GRACO ONE SEAL XHD ( SPRAY PAINTING ) Repair Kit Airmotor Graco REPAIR KIT LOWER NEW KING SILVER PLUS AIRLESS GUN ( SPRAY PAINTING )

Helmet Eastsun

Kubota

Turbocharger

RPB

BREATING FILTER RPB FILTER CARTRIDGE 3100 & AFC 1100 RPB NOVA 1 & 3 ( BLASTING )

Speedo

BLAST HOSE & ACCESSORIES CLAW COUPLING ( BLASTING ) LONG VENTURI NOZZLE POP-UP VALVE

turbocharger

Turbocharger 49189-00992

Windblast

Blast Hose & Accessories Breating Filter Windblast Helmet Windblast Holder Nylon 1 1/4" Windblast Long Ventury Nozzle Windblast Moisture Separator Windblast 1 1/2"

Windtech

Airless Hose Windtech Airless Pump 63:1 Windtech Airless Windtech Moisture Separator 1-1/2" Windtech Repair Kit Lower Pump Windtech Silver Plus Gun Windtech / S-Plus Gun Windtech

Zinc Anode

Zinc Anode S-10 ZAP Zinc Anode S-3 ZAP Zinc Anode S-4 ZAP Zinc Anode S-6 ZAP Zinc Anode S-8 ZAP Zinc Anode S-9 ZAP

CLAW COUPLING (BLASTING)

Claw Couplings are a symmetric quick coupling system with two claws each, which are connected by simultaneously applying force and rotating the two claws to be 45° apart.

BLAST NOZZLE HOLDER ( BLASTING )

All nozzle holders are manufactured to fit externally over the blast hose. Internal grip rings bite into the blast hose for a safe and secure fit, and retaining screws provide additional holding power without penetrating the inner hose layer.

BLAST HOSE (YELLOW) ( BLASTING )

Classic shot blast hose with excellent tube quality for conveying highly abrasive media such as quartz sand, steel shot, corundum, glass, etc. Features: Very long service life due to abrasion resistant tube Antistatic construction prevents the build-up of static electricity

SAFETY CABLE HOSE

To prevent serious injury due to hose or coupling failure, add a whiplash at each hose connection and from equipment to hose, and install it in the fully extended position for proper safety assurance. Spring-loaded loops in the cable ends open easily to slip over the couplings for a firm grip on the hose.

Elcometer 99 Cross Hatch Coating Adhesion Test Tape

The Elcometer 99 Adhesion Test Tape, also known as ASTM Tape, is used in conjunction with both the Elcometer 107 Cross Hatch Cutter and the Elcometer 1542 Cross Hatch Adhesion Tester as a way of instantly assessing the quality between the bond and substrate, quickly, easily and efficiently.

Elcometer 107 Cross Hatch Cutter

The Elcometer 107 Cross Hatch Cutter for adhesion tests provides an instant assessment of the quality of the bond to the substrate. Due to its rugged construction this cross hatch gauge is ideal for thin, thick or tough coatings on all surfaces. An ideal field or laboratory test. Robust design Large, non slip grip Ideal for thin, thick or hard coatings A quick change, 4 sided cutter allows adhesion testing on a wide range of coating thicknesses (1mm, 1.5mm, 2mm and 3mm) The Elcometer 107 Cross Hatch Cutter for adhesion testing is available as a Basic or Full Kit.